Browse all practice questions for the Commercial Comprehensive 2 Practice Exam. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Commercial Comprehensive 2 Practice Exam course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • What range of wire sizes is most commonly used for light and power installations?
  • What is the voltage drop for a 120V, single-phase, two-wire branch circuit, 100' long, using copper conductors of 6,530 circular mils with a noncontinuous load of 13A?
  • Which elements are typically reviewed in a rent roll analysis to gauge concentration risk?
  • Which element is critically important for ensuring effective grounding in electrical systems?
  • What is a diamond commonly recognized as a symbol for?
  • The requirements for grounding of services are located in _____.
  • Which contacts in magnetic contactors are considered normally open (NO)?
  • What are lighting contactors rated for?
  • What is the maximum resistance to ground for rod, pipe, and plate electrodes?
  • Define a hold cost in investment modeling and explain how it is used in hold-period analysis.
  • What is one major advantage of bimetallic overload relays?
  • Which lender strategy is commonly used to mitigate losses when borrowers face temporary distress?
  • What is the minimum thickness required for plate electrodes made of copper?
  • What is the required circuit ampacity for a noncontinuous, three-phase load of 6kW at 208V?
  • What is a ground fault?
  • What does the 'TI allowance' typically impact in a lease pro forma?
  • What term refers to the time-current relationship among multiple overcurrent devices connected in series?
  • Continuous loads are calculated at what percentage of the maximum current rating of the overcurrent device?
  • What is the minimum percentage requirement for a main bonding jumper according to NEC?
  • Low voltage remote control switching relays utilize what type of coil?
  • What is a loan workout and which strategy is commonly used to mitigate losses when a borrower misses terms?
  • What is the load center length for a branch circuit with noncontinuous loads of 20A at 60' and 50A at 125'?
  • According to the NEC®, the ampacity of branch circuit conductors must be derated when there are more than how many current-carrying conductors in a raceway?
  • The maximum value of a short circuit current from line-to-ground _____.
  • Emergency lighting circuits commonly utilize which type of relay?
  • Which component in a motor overload relay senses current?
  • Absorption rate is used in CRE to measure space leased over a period and to inform what leasing strategy consideration?
  • Under MACRS, which statement correctly describes depreciation for commercial real estate?
  • How do CAM reconciliations affect tenant operating expenses and landlord NOI accuracy?
  • What does the term "temper" refer to in the context of conductors?
  • The bonding jumper for multiple disconnecting means is located _____.
  • Which statement describes a floating-rate loan in CRE financing?
  • In lease economics, distinguish between personal property and fixtures, and explain why classification matters for CAM and depreciation.
  • Which statement about a Gross lease is correct?
  • What are the two classifications of overload relays?
  • When placing low-voltage and high-voltage cables in parallel runs, what is the minimum separation required?
  • In electrical engineering, why is it important to monitor dropout values?
  • In a magnetic normally open (N.O.) contactor, when is the circuit closed?
  • What is the difference among ownership structures (sole proprietorship, partnership, LLC, corporation) in CRE for liability and tax purposes?
  • In a residential electrical setting, what is the appropriate method for assessing branch circuit capacity?
  • In a net or modified gross lease, what is the difference between an expense stop and rent escalations?
  • What is the current-carrying capacity for No. 6 THWN aluminum conductors at an ambient temperature of 38°C?
  • Which of the following is considered an acceptable grounding electrode?
  • What is the total load required by the NEC® for two appliance branch circuits plus a laundry branch circuit?
  • What can be a consequence of modifying the Armature spring forest adversely?
  • Where would one find the physical properties of a No. 4/0 copper conductor?
  • Why is it critical to identify the physical properties of a No. 4/0 copper conductor?
  • What factor affects the size of the conductor necessary for a given load in a circuit?
  • In the context of electrical safety, what does "grounding" primarily refer to?
  • How does phased development impact pro forma projections and risk assessment?
  • What must be considered when determining the size of the conductor required to connect an electrical load?
  • What is a probable cause for a relay failing to drop out?
  • What is the purpose of a grounding electrode conductor?
  • What type of adjustments might result in higher dropout values in electric circuits?
  • When is the ground fault cleared?
  • What is the interrupting rating of an FH-type circuit breaker?
  • What is the significance of voltage drop limits in electrical installations?
  • Which component is used to control large electrical loads through low-voltage signals?
  • What happens when the operating coil of a relay is energized?
  • Which component must be connected to the neutral terminal bus of a main distribution panel?
  • Which of the following statements is true about solid wire?
  • What are common risk management strategies for CRE assets, including diversification and hedging interest rate risk?
  • Which of the following is true of the neutral in a grounded system?
  • Which type of breaker is known for its ability to reset after a fault condition?
  • What is a common application for contactors in industrial settings?
  • What is the rated capacity of dual-element fuses for a motor based on its horsepower?
  • The purpose of a grounding electrode system is to _____.
  • Debt yield is calculated as which of the following formulas?
  • What term describes contacts that are together when the relay is not energized?
  • What is a characteristic of magnetic contactors?
  • Where is the normal location to provide overcurrent protection in an electrical circuit?
  • What type of circuit is typically activated by overload relays in machines involved in continuous processing?
  • What is the motor full-load current for a motor with a nameplate rating of 50hp, 460V, 3Ø?
  • What is the formula for debt service coverage ratio (DSCR) and its typical underwriting threshold for a commercial property?
  • What is typically the required ampacity for receptacles in residential settings?
  • What type of load is indicated by a noncontinuous load in electrical circuits?
  • What is the typical control voltage range for solid state relays?
  • Which component is crucial for ensuring safety in high-voltage systems by interrupting current flow?
  • What is CAM in commercial leasing, and how is it typically reconciled at year-end?
  • When a ground rod is installed, the top of the rod must be positioned _____.
  • What is the maximum percentage for the overcurrent protection device rating in relation to the primary current rating of resistance welders?
  • What is the purpose of applying a correction factor in electrical installations?
  • What is the diameter in inches of a conductor that measures 40 mils?
  • SNDA stands for Subordination, Non-Disturbance, and Attornment; what is its primary role?
  • What is the recommended maximum voltage drop for conductors, feeders, and branch circuits combined?
  • Conductors must be derated when installed in conduit _____.
  • What is the operating expense ratio (OER) formula?
  • Differentiate between equity multiple and IRR as investment metrics for commercial properties.
  • The key to successfully clearing ground fault currents is _____.
  • In CRE appraisal, which statement best describes the difference between the income capitalization approach and the cost approach?
  • What type of marking is commonly used to identify grounded conductors larger than No. 6 AWG?
  • What is the formula for EGI (effective gross income) in relation to PGI (potential gross income)?
  • What are the key timelines for a like-kind 1031 exchange?
  • Which statement correctly contrasts direct capitalization and the discounted cash flow (DCF) approach for valuing a property?
  • What is the like-kind property requirement in a 1031 exchange?
  • What characteristic do class A devices specifically protect against?
  • Which factor is affected by the Armature spring forest?
  • Where is the normal current rating of a circuit breaker located?
  • What size copper conductor would be required for a 240V, 1Ø circuit supplying a noncontinuous load of 27.5A at a distance of 145', and a maximum voltage drop of 3%?
  • Which type of device is defined by UL as tripping at a fault current of 6mA or more?
  • How is the lighting load determined for multiple incandescent and fluorescent lights?
  • What must cartridge fuses used for branch circuit protection be marked with?
  • What type of action is a contactor described as if it depends on current flow?
  • What is a capital stack, and why is it important in financing a CRE project?
  • What is an estoppel certificate and why is it important in CRE transactions?
  • Where are mechanically held contacts commonly found?
  • What type of electrical safety device detects ground faults?
  • What is the load center distance for a 208V, four-wire, three-phase branch circuit with fixed noncontinuous loads?
  • How is the size of the equipment grounding conductor (EGC) determined?
  • What is the total ampacity for a 120V branch circuit consisting of four duplex receptacles rated noncontinuous duty and six duplex receptacles rated continuous duty?
  • Which type of GFCI receptacle provides protection only at the installation point?
  • When assessing the performance of electrical systems, what key aspect is often overlooked but critical?
  • What is commonly used to secure equipment grounding conductors to metallic outlet boxes?
  • What type of overload protection is often renewable?
  • How deep must a ground ring consisting of 20' of No. 2 bare copper be buried?
  • In the context of electrical systems, what does a higher dropout value indicate?
  • According to industry standards, remote control wiring must be installed in compliance with which article?
  • Which of the following is an NEC® requirement for grounding and bonding?
  • Which environmental liabilities are typically addressed during due diligence with Phase I/II assessments, testing, remediation, and disclosures?
  • A short circuit is a conducting connection between _____.
  • To maintain a maximum of 3% voltage drop in a 120V circuit, what is the maximum voltage drop allowed?
  • What could be a critical focus area when assessing higher dropout values?
  • Gross potential income is best described as what?
  • What is the effect of a properly functioning motor overload relay?
  • Which set of financing covenants is commonly used by lenders in CRE loans?
  • What is the allowable voltage for a household range's demand load calculated as?
  • Which statement best describes when Phase II Environmental Site Assessment is triggered?
  • Which statement correctly defines net operating income (NOI) in relation to effective gross income (EGI)?
  • Why is debt yield important in underwriting?
  • What is a key feature of solid state relays that differentiates them from traditional relays?
  • Which component is commonly used to mitigate risk by setting aside funds to cover unexpected costs and vacancies in CRE assets?
  • Going-in cap rate and exit cap rate: which statement is correct regarding their use and impact on value?
  • How should parallel runs of low-voltage and high-voltage cables be ideally configured?
  • LTV ratio is defined as which of the following?
  • For a given load and length, the branch circuit voltage drop should not exceed _____.
  • A separately derived system is a premises wiring system that is _____.
  • What method is known for testing ground resistance using an earth ground resistance tester?
  • What is the primary purpose of property insurance for a commercial property?
  • What is the load for 10 feet of multi-outlet assembly used to supply several loads simultaneously?
  • What are key indicators of a submarket's investment viability, including rent growth, vacancy trends, and supply pipeline?
  • In terms of electrical safety, a grounded system helps to _____.
  • Which item is NOT typically included in a commercial property due diligence checklist?
  • What is a likely impact on dropout rates when making adjustments to mechanical elements like the Armature spring forest?
  • Differentiate between zoning variances and rezoning; when might each be pursued?
  • When connected to 15A or 20A multi-outlet general-purpose branch circuits, which of the following shall not exceed 50% of the branch circuit ampere rating?
  • Which item is commonly reviewed to assess environmental risk in CRE due diligence?
  • What is the purpose of equipment grounding?
  • What activates an Opto-isolated solid state relay?
  • At what height should the low voltage panel enclosure typically be installed?
  • What color is generally used on the labels of standard interrupting capacity circuit breakers?
  • What is a 1031 exchange primarily designed to accomplish?
  • In a separately derived system, what does the equipment bonding jumper connect?
  • The minimum diameter of galvanized pipe allowed for a grounding electrode is _____.
  • Which type of fuses provide motor overload protection but are non-renewable?
  • Which statement about flood risk considerations for CRE and NFIP is most accurate?
  • What is the typical purpose of tenant improvements (TI) allowances, and how are they amortized in rent measurements?
  • Which of the following is NOT a market analysis driver for commercial real estate?
  • What distinguishes a non-feed through GFCI from other types?
  • What describes a low-voltage control circuit?
  • Which method is acceptable for identifying grounded conductors larger than No. 6 AWG?
  • How do you calculate net present value (NPV) of a multi-year income property investment, and what discount rate should be used?
  • What is the square mil area of a conductor that is 0.250" on all sides?
  • In a practical scenario, what must a technician evaluate when dropout values rise?
  • Which organizations are responsible for testing and listing circuit breakers?
  • In a net-net lease, which costs is the tenant typically responsible for?
  • Which of the following statements best describes what DSCR represents in underwriting?
  • In which section of the NEC can recommended maximum voltage drops be found?
  • What is a deed restriction, and how can it affect property value or use?
  • How far apart must two grounding electrodes be if a second is required?
  • Which statement best contrasts a build-to-suit lease with ready-to-occupy space?
  • What is a triple-net (NNN) lease, and what is its typical implication for landlord and tenant?
  • Which statement about title insurance is true?
  • Air conditioning overcurrent protective devices can never exceed what percentage of the motor-rated load current or the branch circuit selection current (whichever is greater)?
  • How is the amperage calculated for a 120V circuit with multiple light fixtures operating continuously for 8 hours a day?
  • Why is vacancy and credit loss allowance included in rent projections?
  • Which of the following could potentially be a result of an increase in dropout values?
  • What is an important aspect of maintaining electrical systems regarding dropout values?
  • What is the primary purpose of performing a rent roll analysis?
  • What is the function of the melting alloy in bimetallic overload relays?
  • If Single-Gang Nail-On non-metallic boxes are used with NM cable, what is required?
  • What must be applied if the ambient temperature exceeds 86°F?
  • If the neutral in a grounded system is not needed for voltage requirements, it _____.
  • Ground fault protection is primarily designed to _____.
  • What is the load for 55' of show window using the linear foot method?
  • Which of the following is an example of capital expenditures (CapEx) to enhance property value?
  • What is the demand load for a household range with a nameplate rating of 11.75kW?
  • What is the maximum size dual-element fuse for a 40hp, 3Ø, 460V motor with a Design Letter D?
  • Which type of wire is characterized as the least flexible form of conductor?
  • The minimum length allowed for driven ground rods under normal conditions is _____.
  • What is the difference between an abstract of title and title insurance, and why is title insurance common in commercial real estate (CRE) transactions?
  • How are circuit breakers typically grouped for identification purposes?
  • A higher absorption rate over a period generally indicates stronger demand and supports which leasing action?
  • Which statement describes the core characteristic of the cost approach in CRE valuation?
  • Which component supplies power to operate a low-voltage switching system?
  • Which factor most directly affects CAM charges recovery in a lease?
  • Which of the following is a market analysis driver for commercial real estate?
  • A proper grounding system will contribute to _____.
  • In hold-period analysis, what scenario would most likely reduce the investor's return due to extended holding?
  • What are the two most common types of overcurrent protective devices?
  • What is the purpose of Phase I and Phase II Environmental Site Assessments, and when are they typically required?
  • System grounding relates to the _____.
  • Which symbol is typically used to represent a separate pilot in electrical schematics?
  • Why are single-element fuses considered suitable for protecting circuit breakers with low interrupting ratings?
  • What is the required circuit ampacity of a noncontinuous, single-phase load of 8.5kW at 277V?
  • What is a sale-leaseback and what strategic benefits can it offer a seller?
  • When considering dropout values, what would increasing the Armature spring forest typically lead to?
  • Which statement best explains replacement reserves vs CapEx in CRE budgets?
  • What is the load center length for a branch circuit with noncontinuous loads of 125A at 80', 75A at 110', and 50A at 100'?
  • What is the total resistance of a two-wire circuit that spans a distance of 200' each way with a resistance of 1.21Ω per 1,000'?
  • Which type of system is mandated to be grounded?
  • What is cash-on-cash return, and what are its key limitations in evaluating a property?
  • NEC Article 240 primarily addresses which aspect of electrical systems?
  • By what percentage must the allowable ampacity for eleven No. 12 THHN copper conductors be adjusted?
  • What is the primary role of circuit breakers in electrical systems?
  • Which statement best describes typical loan characteristics for commercial real estate financing?
  • Which type of drawing helps when sizing fuses for a given application?
  • Which of the following must have at least 2 square feet of surface area exposed to the surrounding earth?
  • Which of the following best describes bonding?
  • What is the total resistance of a two-wire circuit spanning a total distance of 1,650' with a conductor resistance of 0.148Ω per 1,000'?
  • What is the operating voltage range for the relay's operating coil?
  • In most residential settings, the available ground fault circuit current typically does not exceed what amount?
  • What is a tenant improvement (TI) allowance, and how is it typically accounted for in pro forma?
  • Which type of relay is known for its resistance to shock and vibration?
  • How could changes in environmental regulation or compliance affect CRE value and operations?
  • Which measurement is used to determine the load capacity in VA for a circuit?
  • In direct capitalization, what does the process use to estimate property value?
  • What is the expected outcome of increasing the Armature spring forest?
  • What is the primary function of a motor overload relay?
  • To keep the voltage drop of a 277V circuit to a maximum of 3%, what is the maximum allowable voltage drop?
  • A current-limiting circuit breaker performs similarly to conventional thermomagnetic circuit breakers at what current threshold?
  • Which statement describes the restrictions and requirements of a 1031 exchange?
  • If the exit cap rate is lowered, what is the expected effect on terminal value in a multi-year projection?
  • Grounding requirements for AC systems are outlined in which NEC sections?
  • What is the most likely application of a contactor?
  • What is the purpose of a shading coil in magnetic contactors?
  • On which architectural element is the location of all lighting fixtures shown?
  • Why would technicians be concerned with dropout values in machinery?
  • Which transformer-supplied system must be grounded if the supply voltage exceeds 150V?
  • What is crucial to the effectiveness of a grounding system?
  • In an electrical system, a short circuit can lead to _____.
  • What is the total lighting load on a 120V circuit for six 100W incandescent lights and four fluorescent fixtures with a ballast rating of 1.5A?
  • What is one of the main benefits of using circuit breakers over fuses?
  • What percentage adjustment is required for a group of conductors within a cable?
  • The continuity between service equipment and enclosures is maintained by _____.
  • How is the show window lighting calculated per linear foot?
  • What might engineers focus on to mitigate the effect of increased dropout values?
  • Which statement about CMBS loans is correct?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy